اره موتوری متداولترین ابزار قطع و تبدیل در جنگلهای شمال کشور محسوب میشود که یکی از مهمترین عیوب آن، ارتعاش دائمی در حین کار است. هدف از این پژوهش، بررسی ارتعاش دست-بازو در عملیات قطع و بینهبری درختان راش در جنگل خیرود نوشهر در استان مازندران است. سه درخت و سه بینه از گونۀ راش انتخاب و با استفاده از دستگاه ارتعاشسنج Bruel & Kjear 2237، همزمان اندازهگیری ارتعاش دست- بازو در دستۀ عقب و دستۀ جلوی اره موتوری در سه جهت x، y و z انجام گرفت. از شاخصهای شدت ارتعاش معادل اره موتوری (aeq)، مقدار کلی ارتعاش اره موتوری (ahv)، ضریب قابلیت انتقال ارتعاش (Tr) و دورۀ مواجهۀ روزانه ((8)A) برای ارزیابی ارتعاش اره موتوری استفاده شد. در مرحلۀ قطع، مقدار aeq در محور x بهطور معنیداری بیشتر از دو محور دیگر در دستههای جلو و عقب بهدست آمد (010/0 = P) و در بینهبری، مقدار aeq در محور x بهطور معنیداری بیشتر از محور z بهدست آمد (008/0 = P). مقدار ahv هنگام قطع درختان (017/0 = P) و بینهبری (013/0 = P) در دستۀ عقب بهطور معنیداری بیشتر از دستۀ جلو بهدست آمد. ضریب Tr در دستۀ عقب اره موتوری در هنگام قطع (78/2) بهطور معنیداری بیشتر از همین دسته در حالت بینهبری (57/2) است (011/0 = P). نتایج نشان داد که شدت ارتعاش در دستۀ عقب بیشتر از دستۀ جلو است که بیانگر لزوم اقدامات سریع از نظر بهبود ارگونومیک دستۀ عقب است.
Nowadays, one of the most popular tools to cut and process the trees in northern forests of Iran is chainsaw. One of its most important defects is constant vibration during operation. The aim of this study was to investigate the hand-arm vibration in beech tree cutting and bucking in Kheyrud forest, Nowshahr, Mazandaran Province. Three beech trees and bucks were selected and hand-arm vibration was measured by using vibrometer Bruel & Kjear 2237 in the back and front handles of chainsaw in three directions x, y, and z. The index of vibration equal value (aeq), vibration total value (ahv), transmitted vibration coefficient (Tr) and daily exposure duration (A(8)) were used to explain the chainsaw vibration. In cutting stage, the value of aeq on the x-axis was significantly higher than the two others in front and back handles (P= 0.010) and in bucking stage, the value of aeq on x-axis is significantly more than z-axis, (P= 0.008). The value of ahv during logging (P= 0.017) and bucking (P=0.013) in the back handle is significantly higher than front handle. Tr coefficient in the back handle of chainsaw while cutting (2.78) was significantly higher than the same handle in bucking (2.75) mode (P= 0.011). The results showed that the values of Tr, aeq and ahv in the back handle is more than front one, hence it needs immediate operation to improve it ergonomically.